Year
2022
Manufacturer
Model
Hours
7,002
Serial Number
AW401378
Condition
Used
Stock Number
D3728
Description
This CAT D8T Waste Handling Dozer with Factory Waste Handling Landfill Arrangement, CAT SU Blade w/ Trash Rack, Rear Striker Bar/Counterweight Assembly, LED Flood Lighting Package, and 28" ES Trapezoidal Tracks.
2,000-hour CAT Powertrain Warranty
Used CAT D8T WH Dozer featuring:
• 2,000-hour CAT Powertrain Warranty
• CAT C15 ACERT Engine
• Block Heater
• Cab (ROPS) w/ A/C
• Cab Air Pre-Cleaner
• Factory Waste Handling Landfill Arrangement
• CAT SU Blade w/ Trash Rack
• 28" ES Trapezoidal Tracks
• Rear Striker Bar/Counterweight Assembly
• Final Drive Seal Guards
• Clamshell Final Drive Seal Guards
• Pivot Shaft Seal Guards
• Engine Pre-Cleaner
• Debris Resistant Radiator
• Fuel Tank Guards
• LED Flood Lighting Package
• Rear View Camera
• Bogie Suspension Rollers
• Powered HD Bottom Guards
• Winch Valve
• High Speed Oil Change
• Rated at 343 HP
• Weight 88,000 LBS
When this D8T WH Dozer arrived in yard, MEL had our local CAT dealer, Toromont CAT, complete the following at 6,993 Hrs:
• Strip all belly pans, covers and panels from machine for power washing
• Completed CAT TA 1 Plus inspection
• Update ECM flash files
• Check for logged & active codes & repaired
• Check for applicable service letters
• Inspected emissions system for servicing - DPF serviced at 5,087 Hrs
• Changed and cut open all oil filters & inspected for contaminates - All Clean
• Inspect magnetic plugs/screens & suction screens - All Clean
• Serviced engine
• Changed fuel tank breather and cleaned filler screen
• Changed transmission and hydraulic breathers
• Changed all air filters and cab filters
• Inspect oils for discoloration
• Changed engine, transmission, hydraulic and final drive oils
• Check oil levels
Completed the following Pressure Checks to ensure within OEM spec:
• Fan pressure & speed - completed fan calibrations.
• Engine RPM high & low idle
• Engine oil high & low idle pressures
• Fuel pressure checks
• Transmission and torque convertor checks
• Torque convertor stall speed
• Full stall boost - full stall speed
• All hydraulic system checks
• All steering system checks
• Brake pressure checks
• Performed all machine calibrations
Based on the CAT dealer inspection, CAT Tech and Marcel Tech completed the following repairs:
Operator Station:
• Removed and cleaned all power and ground cables supplying cab power
• Replaced main power junction block under cab
• Replaced A/C compressor
• Replaced A/C drier
• Replaced throttle switch
• Replaced door seals
• Replaced cracked cab glass
• Installed NEW operator seat
Machine frame and chassis:
• Shutdown switch replaced
• Cleaned all battery cables and disconnect switch
• Replaced fuel drain shut off valve
• Cleaned all battery cables on starter
• Replaced all equalizer bar pads
• Replaced both track adjuster canon seals
• Repaired belly pan mounts
• Replaced lift cylinder hoses with NEW
Powertrain and Engine systems:
• Installed a NEW front crank seal
• Replaced transmission wall harness
• Replaced coolant pressure sensor
• A NEW ARD head was installed along with NEW seals and a spark plug
• Replaced DEF injector
• Test of the aftertreatment system was performed successfully
• Installed NEW o-rings on aux drive cover plates
• Installed a NEW transmission Input shaft seal and yoke
• Replaced worn / leaking powertrain hoses
• Replaced lower rad hose clamps
• Replaced heater hose shutoff valves
• Installed all NEW bearings in all idler pulleys
• Installed NEW belt tensioner
• Installed NEW serpentine belt
• Installed REBUILT Alternator
• Cleaned and installed all battery cables
• Replaced faulty fuel pressure regulator and line check valve
• Ran and tested machine after all repairs and verified no leaks are present and machine operates as it should
Marcel Equipment completed the following repairs:
• Completed required cosmetic & welding repairs
• Completed required blade repairs
• Replaced worn blade pins & bushings
• Line bored blade joints where required
• Prepped machine for sandblasting & painting
• Sandblasted, primed, painted, NEW decals and detailed machine
• Assembled machine once completed
• Greased machine
This CAT D8T WH Tractor is Completed and Work Ready.
The following are repairs completed by CAT Dealer prior to Marcel Equipment owning the machine:
At 6,690 hours, performed 2000 hour service
At 6,690 hours, installed NEW batteries
At 6,690 hours, REBUILT lift cylinders
At 6,663 hours, NEW track shoes installed
At 6,663 hours, track bushings turned
At 6,663 hours, NEW sprocket segments installed
At 6,663 hours, NEW batteries installed
At 6,663 hours, RESEALED both blade lift cylinders
At 6,663 hours, NEW cutting edges installed
At 6,663 hours, UPDATED all software
At 5,087 hours, SERVICED DPF
At 4,245 hours, NEW track cannon seal & bearings installed
At 4,245 hours, RESEALED track adjusters
At 4,245 hours, installed NEW track guide wear bars
At 4,245 hours, installed NEW alternator